羅茨風機在運行的過程中有時候會出現機體溫度過高的的情況，出現這種情況時需要及時找出原因并且處理掉：
During the operation of Roots blower, sometimes the body temperature is too high. In this case, it is necessary to find out the cause and deal with it in time:
一、羅茨風機機體溫度過高的原因有：
1、 The reasons for the excessive temperature of Roots blower body are as follows:
1. 羅茨風機油箱內油太多、太稠、太臟；
1. The oil in the oil tank of Roots blower is too much, too thick and dirty;
2. 過濾器或消聲器堵塞；
2. The filter or muffler is blocked;
3. 壓力高于規定值；
3. The pressure is higher than the specified value;
4. 葉輪過度磨損，間隙大；
4. The impeller is excessively worn and the clearance is large;
5. 羅茨風機通風不好，室內溫度高，造成進口溫度高；
5. The roots blower has poor ventilation and high indoor temperature, resulting in high inlet temperature;
6. 運轉速度太低，皮帶打滑。
6. The running speed is too low and the belt slips.
二、羅茨風機機體溫度過高處理方法：
2、 Treatment method for excessive temperature of Roots blower body:
1. 降低油位或挾油；
1. Reduce the oil level or trap oil;
2. 除去堵物；
2. Remove the blockage;
3. 降低通過鼓風機的壓差；
3. Reduce the differential pressure through the blower;
4. 間隙；
4. Clearance;
5. 羅茨風機開設通風口，降低室溫；
5. The roots blower is provided with a vent to reduce the room temperature;
6. 加大轉速，防止皮帶打滑
6. Increase the speed to prevent the belt from slipping
羅茨風機如果發現有異常要及時的處理，保證設備的正常運轉，提高設備的使用壽命。
If any abnormality is found in Roots blower, it shall be handled in time to ensure the normal operation of the equipment and improve the service life of the equipment.
為了確保用戶收到的三葉羅茨鼓風機萬無一失，都會進行試機檢查，那么客戶在收到貨之后，要做好哪些開箱檢查呢？
In order to ensure that the three leaf roots blower received by the user is safe, the commissioning inspection will be carried out. What unpacking inspection should the customer do after receiving the goods?
（1）根據三葉羅茨鼓風機裝箱清單，核對葉輪、機殼和其他部件是否齊全；
(1) Check whether the impeller, casing and other parts are complete according to the packing list of three leaf roots blower;
（2）葉輪旋轉方向應符合三葉羅茨鼓風機技術文件的規定；
(2) The rotation direction of the impeller shall comply with the provisions of the technical documents of the three blade roots blower;
（3）進、排氣口應有蓋板嚴密遮蓋，防止塵土和雜物進入；
(3) The air inlet and exhaust ports shall be tightly covered with cover plates to prevent dust and sundries from entering;
（4）檢查三葉羅茨鼓風機外露部分各加工面的防銹情況，和轉子是否發生明顯的變形或嚴重銹蝕、碰傷等。
(4) Check the rust prevention of each processing surface of the exposed part of the three blade roots blower and whether the rotor is obviously deformed or seriously rusted, bruised, etc.
以上就是應做好的三葉羅茨鼓風機收貨開箱檢查，如果發現有問題要及時與廠家聯系，我們立即為大家更換。
The above is the unpacking inspection of three blade roots blower. If there is any problem, contact the manufacturer in time and we will replace it immediately.
The above is a detailed introduction about Shandong roots blower. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://m.rohs-international.com/
TEL:400-9901-557
TEL:18678880998
公司地址：山東省濟南市章丘區相公街道大康村村南
濟南道源豐達機械制造有限公司
備案號：魯ICP備2022009540號-1 魯公網安備37018102000745號
